|
NOT
SCAQMD 102 & 1151 Rule Compliant
5410 is an economical protective coating for chassis,
engine compartments, and miscellaneous parts to
refinish. It has excellent adhesion and impact
resistance. 5410 is resistant to fuels when thoroughly
cured using 5 STAR #5132 Enamel Hardener. Offered in
gloss black.
PRODUCT DESCRIPTION:
5410 Frame Black is an economical protective coating for
chassis, engine compartments, and miscellaneous parts to
refinish. It has excellent adhesion and impact
resistance. 5410 is resistant to fuels when thoroughly
cured using 5 STAR #5132 Enamel Hardener. Offered in
Gloss Black. NOT SCAQMD 102 & 1151 Rule
Compliant.
|
FEATURES: |
| |
•
4.6 VOC
•
Ready to Spray!
•
Gloss Black
•
Excellent Adhesion
Characteristics
•
Superior Impact
Resistance
•
Fast Drying |
| PRODUCTS &
COLOR: |
| |
Gallon/cs |
Quarts/cs |
Pint/cs |
4.6 VOC Frame Black
(Gloss Black Paint for Chassis) |
#5410-1 |
#5410-4 |
|
|
If Desired: Synthetic
Enamel Hardener |
|
|
#5132-8 |
|
SURFACE PREPARATION:
Prior to repair,wash the surface with mild detergent and
hot water,making sure to rinse well and dry with a clean
dry cloth. Solvent clean with 5 STAR #5902 FinalWipeWax
& Grease Remover to remove any contaminants prior to
sanding or bodywork. Final sand bare metal with 150 –
220 grit sandpaper. Final sand painted surfaces with
220-320 grit sandpaper. Final clean with 5 STAR
#5902,making sure surface is clean and dry. Final wipe
using a tack cloth.
|
MIXING DIRECTIONS:
READY TO SPRAY. NO MIXING REQUIRED |
OPTIONAL MIX BY VOLUME - For Added Durability
& Protection
Mix the components in the order and ratio
indicated below. Stir thoroughly after adding
each item.
|
| |
|
#5410 FRAME BLACK Paint |
8 Parts |
|
#5132 Enamel Hardener |
1 Parts |
| MIX
RATIO IN OUNCES |
| COLOR |
8 |
16 |
24 |
32 |
48 |
64 |
| HARDENER |
1 |
2 |
3 |
4 |
6 |
8 |
|
APPLICATION & DRY TIME DIRECTIONS:
Allow appropriate dry times for primers and
sealers. Strain paint prior to application. Apply one
medium-wet coat and allow 10 minutes flash or until
surface is hand slick. Apply a second full wet coat. For
best results, do not apply more than 2 coats.
| BAKING - 5410 MUST BE
HARDENED IN ORDER TO BAKE OR FORCE DRY |
| Full
Bake Cycle: |
Allow 30
minutes purge. Bake 30 minutes - 1 hour
at 140°F. Allow a 2 hour cool down prior
to assembling. |
|
POT
LIFE:
4 – 6 hours at 75°F (if hardened with 5132). Do not
try to thin color after thickening has occurred – do not
use. Clean equipment immediately after use. Note:
Accelerators, reducers, and temperature will affect pot
life.
COMPATIBLE SUBSTRATES:
Bare Steele.
| GUN SETUP:
|
Fluid Tip |
Air Pressure |
| HVLP Gravity |
1.3mm - 1.4mm |
6 - 10 PSI at
the cap |
| HVLP Siphon |
1.5mm - 1.8mm |
6 - 10 PSI at the cap |
| Con.Gravity |
1.3mm - 1.4mm |
50 PSI at the gun |
| Con. Siphon |
1.5mm - 1.8mm |
50 PSI at the gun |
|
DATA: |
|
|
Dust Free - 20
minutes
(will vary with hardener & reducer) |
Solvent
Resistance - Xylene pass 100 rubs
(w/ 5132) |
| Dry to Handle -
2 hours |
Recommended Coats - 2 |
| VOC as applied -
4.6 lbs/gal |
DFT per coat +/- .20 mils |
| Mixed Volume
Solids - 36.62% |
Theoretical Coverage - 587
sq. ft @ 1 mil.DFT |
Film Hardness -
2H
(w/ 5132 Hardener) |
|
NOTES:
Use in shop temperatures that are maintained above
75°F for the first 24-hours of the cure cycle. Ensure
surfaces are up to shop temperature prior to work.
Ensure proper metal conditioning/preparation procedures
in early stages are followed.Use a mixing cup for
accurate volume measurements. 5410 will be water
resistant in 24-hours. Note: Do not allow raindrops to
dry on a new finish for the first 3 – 4 days to prevent
staining.
CLEAN UP:
Clean spray equipment immediately after use with
Urethane Grade Reducer or 5 STAR #5414 VirginWash
Thinner. Do not leave material in spray gun.
DISPOSAL:
Dispose of all paint and paint related materials in
accordance with state and local regulations.
SAFETY INFORMATION – FOR INDUSTRY USE ONLY:
Danger: Vapor harmful.May
affect the brain or nervous system causing dizziness,
headache, or nausea. May cause eye, skin, nose, and
throat irritation. Harmful if swallowed.
Precautions: Vapors may ignite explosively.
Keep away from heat, sparks, and flame. Vapors may cause
flash fire. Do not smoke. Extinguish all flames and
pilot lights, and turn off stoves, heaters, electric
motors and other sources of ignition during use and
until all vapors are gone. Prevent buildup of vapors by
opening all windows and doors to achieve
cross-ventilation. Use only with adequate
ventilation. Do not breathe vapor or spray
mist. Do not get in eyes, on skin or clothing. Wash
thoroughly after handling. Wear solvent resistant
gloves. The material is designed for application only by
professionally trained personnel using proper equipment
under controlled conditions, and is not intended for
sale to the general public. KEEP OUT OF REACH OF
CHILDREN. ABI - Autobody Brands International a division
of IAMG - International Autobody Marketing Group.
Scottsdale, AZ - www.autobodybrands.com |
HMS Warehousing Corporation
